prikaz prve stranice dokumenta Postupak toplinske obrade strojnog dijela RM.18-PT.85
Access restricted to students and staff of home institution
undergraduate thesis
Postupak toplinske obrade strojnog dijela RM.18-PT.85
Rijeka: University of Rijeka, Faculty of Engineering, 2018. urn:nbn:hr:190:036195
Martinković, Rebeka
University of Rijeka
Faculty of Engineering
Department of Materials Science and Engineering
Section of Materials Engineering

Institutional repository: Repository of the University of Rijeka, Faculty of Engineering

Cite this document

Martinković, R. (2018). Postupak toplinske obrade strojnog dijela RM.18-PT.85 (Undergraduate thesis). Rijeka: University of Rijeka, Faculty of Engineering. Retrieved from https://urn.nsk.hr/urn:nbn:hr:190:036195

Martinković, Rebeka. "Postupak toplinske obrade strojnog dijela RM.18-PT.85." Undergraduate thesis, University of Rijeka, Faculty of Engineering, 2018. https://urn.nsk.hr/urn:nbn:hr:190:036195

Martinković, Rebeka. "Postupak toplinske obrade strojnog dijela RM.18-PT.85." Undergraduate thesis, University of Rijeka, Faculty of Engineering, 2018. https://urn.nsk.hr/urn:nbn:hr:190:036195

Martinković, R. (2018). 'Postupak toplinske obrade strojnog dijela RM.18-PT.85', Undergraduate thesis, University of Rijeka, Faculty of Engineering, accessed 23 December 2024, https://urn.nsk.hr/urn:nbn:hr:190:036195

Martinković R. Postupak toplinske obrade strojnog dijela RM.18-PT.85 [Undergraduate thesis]. Rijeka: University of Rijeka, Faculty of Engineering; 2018 [cited 2024 December 23] Available at: https://urn.nsk.hr/urn:nbn:hr:190:036195

R. Martinković, "Postupak toplinske obrade strojnog dijela RM.18-PT.85", Undergraduate thesis, University of Rijeka, Faculty of Engineering, Rijeka, 2018. Available at: https://urn.nsk.hr/urn:nbn:hr:190:036195

Metadata
TitlePostupak toplinske obrade strojnog dijela RM.18-PT.85
Title (english)Heat treating process of workpiece RM.18-PT.85
AuthorRebeka Martinković
MentorDario Iljkić (mentor)
Committee memberKristian Lenić (predsjednik povjerenstva)
GranterUniversity of Rijeka
Faculty of Engineering
(Department of Materials Science and Engineering)
(Section of Materials Engineering)
Rijeka
Defense date and country2018-09-18, Croatia
Scientific / art field,
discipline and subdiscipline		TECHNICAL SCIENCES
Mechanical Engineering
Abstract
Postoje različite vrste toplinskih obrada čelika kojima je cilj poboljšavanje svojstava materijala, kao npr. povećanje žilavosti, duktilnosti, tvrdoće, smanjenje unutarnjih naprezanja i dr. Kako bi se mijenjala svojstva, potrebno je mijenjati mikrostrukturu čelika, a to se postiže različitim parametrima zagrijavanja, progrijavanja i hlađenja. U ovom radu praktični dio zadatka jest povećati tvrdoću strojnom dijelu RM.18-PT.85 koji je izrađen iz materijala C45E (Č.1531) i to toplinskom obradom kaljenja, a zatim smanjiti zaostala naprezanja u materijalu niskotemperaturnim popuštanjem. Kaljenje se vrši iznad temperature austenitizacije nakon čega se gasi u ulju. Na strojni dio postavljen je zahtjev tvrdoće koji mora biti u rasponu 550 +5 HRC. Tvrdoća se prije toplinskih obrada mjeri Rockwellovom HRB metodom te ona iznosi 88 HRB. Nakon istih ponavlja se mjerenje Rockwellovom HRC metodom. Dobivena tvrdoća strojnog dijela iznosi 57 HRC pa stoga krajnji rezultat zadovoljava traženi zahtjev.
Abstract (english)
There are different types of heat treatments of steel with the aim of improving material properties such as increased toughness, ductility, hardness, reduction of internal stress etc. In order to change the properties, it is necessary to change the microstructure of the steel, which is achieved by different heating and cooling parameters. In this paper, the practical part of the task is to increase the hardness of the machining part RM.18PT.85 which is made from material C45E (Č.1531) by heat treatment of hardening and after that reduce the residual internal stresses by low temperature tempering. During the hardening treatment the machine part is heating above the austenitization temperature and then the part is quenching in the oil. The machine part has a hardness requirement that must be in the range of 550 +5 HRC. Hardness before these heat treatments is measured by the Rockwell HRB method and it amounts 88 HRB. After heat treatments, measuring the hardness is repeated by the Rockwell HRC method. The resulting hardness of the machine part is 57 HRC so the end result meets the required demand.
Keywords
Keywords (english)
Languagecroatian
URN:NBNurn:nbn:hr:190:036195
Study programmeTitle: Mechanical Engineering
Study programme type: university
Study level: undergraduate
Academic / professional title: sveučilišni/a prvostupnik/ prvostupnica (baccalaureus/baccalaurea) inženjer/inženjerka strojarstva (sveučilišni/a prvostupnik/ prvostupnica (baccalaureus/baccalaurea) inženjer/inženjerka strojarstva)
Type of resourceText
File originBorn digital
Access conditionsAccess restricted to students and staff of home institution
Terms of useLicence In copyright icon
Created on2018-11-07 09:48:54