prikaz prve stranice dokumenta Postupak toplinske obrade strojnog dijela TK.19-DT.52
Access restricted to authenticated users
master's thesis
Postupak toplinske obrade strojnog dijela TK.19-DT.52
Rijeka: University of Rijeka, Faculty of Engineering, 2019. urn:nbn:hr:190:388639
Koraca, Toni
University of Rijeka
Faculty of Engineering
Department of Materials Science and Engineering

Institutional repository: Repository of the University of Rijeka, Faculty of Engineering

Cite this document

Koraca, T. (2019). Postupak toplinske obrade strojnog dijela TK.19-DT.52 (Master's thesis). Rijeka: University of Rijeka, Faculty of Engineering. Retrieved from https://urn.nsk.hr/urn:nbn:hr:190:388639

Koraca, Toni. "Postupak toplinske obrade strojnog dijela TK.19-DT.52." Master's thesis, University of Rijeka, Faculty of Engineering, 2019. https://urn.nsk.hr/urn:nbn:hr:190:388639

Koraca, Toni. "Postupak toplinske obrade strojnog dijela TK.19-DT.52." Master's thesis, University of Rijeka, Faculty of Engineering, 2019. https://urn.nsk.hr/urn:nbn:hr:190:388639

Koraca, T. (2019). 'Postupak toplinske obrade strojnog dijela TK.19-DT.52', Master's thesis, University of Rijeka, Faculty of Engineering, accessed 23 December 2024, https://urn.nsk.hr/urn:nbn:hr:190:388639

Koraca T. Postupak toplinske obrade strojnog dijela TK.19-DT.52 [Master's thesis]. Rijeka: University of Rijeka, Faculty of Engineering; 2019 [cited 2024 December 23] Available at: https://urn.nsk.hr/urn:nbn:hr:190:388639

T. Koraca, "Postupak toplinske obrade strojnog dijela TK.19-DT.52", Master's thesis, University of Rijeka, Faculty of Engineering, Rijeka, 2019. Available at: https://urn.nsk.hr/urn:nbn:hr:190:388639

Metadata
TitlePostupak toplinske obrade strojnog dijela TK.19-DT.52
Title (english)Heat treating process of workpiece TK.19-DT.52
AuthorToni Koraca
MentorDario Iljkić (mentor)
Committee memberKristijan Lenac (predsjednik povjerenstva)
Committee memberRoberto Žigulić (član povjerenstva)
Committee memberOzren Bukovac (član povjerenstva)
GranterUniversity of Rijeka
Faculty of Engineering
(Department of Materials Science and Engineering)
Rijeka
Defense date and country2019-09-25, Croatia
Scientific / art field,
discipline and subdiscipline		TECHNICAL SCIENCES
Mechanical Engineering
Abstract
Tema ovog diplomskog rada je toplinska obrada strojnog dijela TK.19-DT.52. U uvodnom dijelu, tj. teorijskom, govori se o čeliku i njegovim svojstvima općenito. Nakon toga opisan je postupak toplinske obrade (poboljšavanja i indukcijskog kaljenja), ispitivanje tvrdoće, fazne promjene u čeliku te TTT dijagram. Opisana je također i metoda kojom se određuju parametri vezani za toplinsku obradu i postrojenje za samu. U praktičnom dijelu izvedena je toplinska obrada poboljšavanja kako bi strojni dio imao visoku granicu tečenja i žilavost. Pošto se tvrdoća tijekom postupka visokotemperaturnog popuštanja smanjila, pristupilo se indukcijskom kaljenju površine strojnog dijela. Tim postupkom postignuta je tvrda površina otpornija na trošenje, a jezgra strojnog dijela ostala je nepromijenjena tj. u jezgri imamo visoku granicu tečenja te visoku žilavost, a na površini tvrdu martenzitnu strukturu. Sa indukcijskim kaljenjem dobivena je tvrda površina strojnog dijela, zahtijevane tvrdoće od 56 HRC-a.
Abstract (english)
The paper presenst the heat treatment of the machine part TK.19-DT.52. The introductory part i.e. the theoretical part presents steel and its properties in general. Afterward are described the procedure of heat treatment (improvement and induction hardening), hardness testing, steel phase changes and TTT diagram. Also is described a method that determines the parameters related to the heat treatment and the plant itself. In the practical part is performed the heat treatment of the enhancement to set a upper limit of flow and toughness to the machine part. As the hardness decreased during the high temperature yielding process, came up to the induction hardening of the surface of the machine part. With this process has been achieved a hard surface more resistant to consume, and the core of the machine part remained unchanged, i.e. in the core we have a high flow limit and high toughness and a hard martensitic structure on the surface. With induction hardening was obtained a hard surface of the machine part with required hardness of 56 HRC.
Keywords
Keywords (english)
Languagecroatian
URN:NBNurn:nbn:hr:190:388639
Study programmeTitle: Mechanical Engineering
Study programme type: university
Study level: graduate
Academic / professional title: magistar/magistra inženjer/inženjerka strojarstva (magistar/magistra inženjer/inženjerka strojarstva)
Type of resourceText
File originBorn digital
Access conditionsAccess restricted to authenticated users
Terms of useLicence In copyright icon
Created on2019-10-25 08:59:27