prikaz prve stranice dokumenta Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a
Access restricted to students and staff of home institution
undergraduate thesis
Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a
Rijeka: University of Rijeka, Faculty of Engineering, 2020. urn:nbn:hr:190:293884
Šestan, Dani
University of Rijeka
Faculty of Engineering
Department of Automation and Electronics
Section of Electronics, Robotics and Automation

Institutional repository: Repository of the University of Rijeka, Faculty of Engineering

Cite this document

Šestan, D. (2020). Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a (Undergraduate thesis). Rijeka: University of Rijeka, Faculty of Engineering. Retrieved from https://urn.nsk.hr/urn:nbn:hr:190:293884

Šestan, Dani. "Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a." Undergraduate thesis, University of Rijeka, Faculty of Engineering, 2020. https://urn.nsk.hr/urn:nbn:hr:190:293884

Šestan, Dani. "Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a." Undergraduate thesis, University of Rijeka, Faculty of Engineering, 2020. https://urn.nsk.hr/urn:nbn:hr:190:293884

Šestan, D. (2020). 'Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a', Undergraduate thesis, University of Rijeka, Faculty of Engineering, accessed 27 November 2024, https://urn.nsk.hr/urn:nbn:hr:190:293884

Šestan D. Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a [Undergraduate thesis]. Rijeka: University of Rijeka, Faculty of Engineering; 2020 [cited 2024 November 27] Available at: https://urn.nsk.hr/urn:nbn:hr:190:293884

D. Šestan, "Izrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a", Undergraduate thesis, University of Rijeka, Faculty of Engineering, Rijeka, 2020. Available at: https://urn.nsk.hr/urn:nbn:hr:190:293884

Metadata
TitleIzrada 8-bitnog binarnog na 3x7-segmentni pokazivač dekodera pomoću EEPROM-a
Title (english)EEPROM based 8-bit binary to 3x7-segment display decoder
AuthorDani Šestan
MentorIvan Volarić (mentor)
Committee memberViktor Sučić (predsjednik povjerenstva)
Committee memberIvan Volarić (član povjerenstva)
GranterUniversity of Rijeka
Faculty of Engineering
(Department of Automation and Electronics)
(Section of Electronics, Robotics and Automation)
Rijeka
Defense date and country2020-09-16, Croatia
Scientific / art field,
discipline and subdiscipline		TECHNICAL SCIENCES
Electrical Engineering
Abstract
U ovom završnom radu opisan je postupak izrade 8-bitnog binarnog dekodera. Izrada dekodera započela je u programu EasyEDA tako što se izradila shema dekodera, te potom pomoću naredbe Convert to PCB izradila podloga za izradu tiskane pločice. Zatim je uslijedila izrada EEPROM programatora koji se temelji na mikrokontroleru Atmega328, te lemljenje komponenata dekodera na izrađenu tiskanu pločicu. Potom slijedi programiranje EEPROM memorije. Kodom koji je napisan u Arduino programu, generirali su se podaci koji su se zapisali na odgovarajuća mjesta u EEPROM memoriji. 8-pinskim muškim header-om odabire se 8-bitni ulazni podatak koji se na rastući brid radnog takta CLK pohranjuje u 2 ulazna registra. Taj podatak dalje ide u EEPROM memoriju čiji su izlazi spojeni na 7-segmentne zaslone. Segmenti triju zaslona pale se na način koji prikazuje Tablica 3.1-1. Podatak s ulaznih registara briše se djelovanjem impulsa CLR, dok pinovi G1 i G2 aktiviraju ulaze u registre.
Abstract (english)
This bachelor thesis describes the process of making an 8-bit binary decoder. The creation of the decoder started in EasyEDA by creating a decoder scheme, and then using the Convert to PCB command to create a base for the fabrication of the printed circuit board. This was followed by the development of an EEPROM programmer based on the Atmega328 microcontroller, and the soldering of decoder components to the fabricated printed circuit board. This is followed by programming the EEPROM memory. The code written in the Arduino program generated data that was written to the appropriate places in the EEPROM memory. With an 8-pin male header, 8-bit input data is selected and stored in 2 input registers on the rising edge of the CLK clock. This data goes further into the EEPROM memory whose outputs are connected to 7-segment displays. The segments of the three displays light up as shown in Table 3.1-1. The data from the input registers is erased by the action of the CLR pulse, while pins G1 and G2 activate the registers' inputs.
Keywords
Keywords (english)
Languagecroatian
URN:NBNurn:nbn:hr:190:293884
Study programmeTitle: Undergraduate University Study of Electrical Engineering
Study programme type: university
Study level: undergraduate
Academic / professional title: sveučilišni/a prvostupnik/prvostupnica (baccalaureus/baccalaurea) inženjer/inženjerka elektrotehnike (sveučilišni/a prvostupnik/prvostupnica (baccalaureus/baccalaurea) inženjer/inženjerka elektrotehnike)
Type of resourceText
File originBorn digital
Access conditionsAccess restricted to students and staff of home institution
Terms of useLicence In copyright icon
Created on2021-10-05 08:21:17