prikaz prve stranice dokumenta KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA
Access restricted to students and staff of home institution
master's thesis
KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA
Slavonski Brod: Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, 2020. urn:nbn:hr:153:250101
Baričević, Josip
Josip Juraj Strossmayer University of Osijek
Mechanical Engineering Faculty in Slavonski Brod

Institutional repository: Repository of Mechanical Engineering in Slavonski Brod

Cite this document

Baričević, J. (2020). KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA (Master's thesis). Slavonski Brod: Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod. Retrieved from https://urn.nsk.hr/urn:nbn:hr:153:250101

Baričević, Josip. "KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA." Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, 2020. https://urn.nsk.hr/urn:nbn:hr:153:250101

Baričević, Josip. "KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA." Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, 2020. https://urn.nsk.hr/urn:nbn:hr:153:250101

Baričević, J. (2020). 'KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA', Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, accessed 26 December 2024, https://urn.nsk.hr/urn:nbn:hr:153:250101

Baričević J. KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA [Master's thesis]. Slavonski Brod: Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod; 2020 [cited 2024 December 26] Available at: https://urn.nsk.hr/urn:nbn:hr:153:250101

J. Baričević, "KONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA", Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, Slavonski Brod, 2020. Available at: https://urn.nsk.hr/urn:nbn:hr:153:250101

Metadata
TitleKONSTRUIRANJE PROIZVODA OD POLIMERNIH MATERIJALA
Title (english)PRODUCTS DESIGN FROM POLYMER MATERIALS
AuthorJosip Baričević
MentorPero Raos (mentor)
Committee memberPero Raos (član povjerenstva)
Committee memberJosip Stojšić (predsjednik povjerenstva)
Committee memberAndrijana Milinović (član povjerenstva)
GranterJosip Juraj Strossmayer University of Osijek
Mechanical Engineering Faculty in Slavonski Brod
Slavonski Brod
Defense date and country2020-09-24, Croatia
Scientific / art field,
discipline and subdiscipline		TECHNICAL SCIENCES
Mechanical Engineering
Abstract
U radu je prikazan kratak pregled vrsta polimera s obzirom na njihovo ponašanje kod povišenih temperatura te je s obzirom na to svojstvo prezentirana podjela na plastomere, elastomere i duromere, gdje su navedeni neki od najzastupljenijih predstavnika pojedine vrste. Sljedeće poglavlje prezentira proces preradbe polimera postupkom injekcijskog prešanja. Poglavlje se bavi samim opisom aktivnosti koje se odvijaju u jednom ciklusu injekcijskog prešanja, zatim se navode najbitniji dijelovi sustava za injekcijsko prešanje uz njihov kratak opis i ulogu u samome sustavu. Kako je cilj ovoga rada prikazati postupak konstruiranja i provjere tehničnosti polimernog proizvoda, prije samoga zadatka prikazan je pregled faza koje se moraju provesti pri konstruiranju polimernog proizvoda. Nakon prethodnog teorijskog opisa polimera, postupka injekcijskog prešanja i uvoda u konstruiranje polimernih proizvoda, nastojalo se objediniti cjelinu primjerom konstrukcije polimernog proizvoda, pridržavajući se pravila konstrukcijskog oblikovanja za injekcijski prešane proizvode. Kako bi se uvjerili u ispravnost prikazanih rješenja provedena je simulacija u programskom paketu Autodeska, Moldflow Adviser-u, u cilju provjere tehničnosti otpreska.
Abstract (english)
The paper presents a short overview of the types of polymers according to their behavior while exposed to increased temperatures and based on that property, the division into thermoplastics, elastomers and thermosets is shown, along with listing some of the most common representatives of each group. The next chapter describes the processing of polymers through injection molding. The chapter deals with elaborating the activities in one cycle of the injection molding, and specifies the most important parts of the injection molding system, including their description and role in the system. Since the goal of this paper is to show the process of designing and testing the technical nature of a polymeric product, before presenting the problem itself, the paper gives an overview of the phases of designing the polymeric product. Following the theoretic description of polymers, the process of injection molding and the introduction into designing polymeric products, the goal is to complete the subject with an example of designing a polymeric product while abiding by the rules of part modelling for products designed for injection molding. In order to test the accuracy of the presented solutions, with the goal of checking the technical nature of the molding, a simulation in the program package of Autodesk, Moldflow Adviser has been conducted.
Keywords
Keywords (english)
Languagecroatian
URN:NBNurn:nbn:hr:153:250101
Study programmeTitle: Graduate Study Mechanical Engineering; specializations in: Design and Product Development, Manufacturing Logistics, Materials Engineering, Engineering Technologies, Power Engineering
Course: Engineering Technologies
Study programme type: university
Study level: graduate
Academic / professional title: magistar/magistra inženjer/inženjerka strojarstva (magistar/magistra inženjer/inženjerka strojarstva)
Type of resourceText
File originBorn digital
Access conditionsAccess restricted to students and staff of home institution
Terms of useLicence In copyright icon
Created on2020-10-14 07:50:46