prikaz prve stranice dokumenta KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA
Access restricted to students and staff of home institution
master's thesis
KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA
Slavonski Brod: Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, 2020. urn:nbn:hr:153:799596
Puhanić, Dominik
Josip Juraj Strossmayer University of Osijek
Mechanical Engineering Faculty in Slavonski Brod

Institutional repository: Repository of Mechanical Engineering in Slavonski Brod

Cite this document

Puhanić, D. (2020). KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA (Master's thesis). Slavonski Brod: Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod. Retrieved from https://urn.nsk.hr/urn:nbn:hr:153:799596

Puhanić, Dominik. "KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA." Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, 2020. https://urn.nsk.hr/urn:nbn:hr:153:799596

Puhanić, Dominik. "KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA." Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, 2020. https://urn.nsk.hr/urn:nbn:hr:153:799596

Puhanić, D. (2020). 'KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA', Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, accessed 24 November 2024, https://urn.nsk.hr/urn:nbn:hr:153:799596

Puhanić D. KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA [Master's thesis]. Slavonski Brod: Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod; 2020 [cited 2024 November 24] Available at: https://urn.nsk.hr/urn:nbn:hr:153:799596

D. Puhanić, "KONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA", Master's thesis, Josip Juraj Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, Slavonski Brod, 2020. Available at: https://urn.nsk.hr/urn:nbn:hr:153:799596

Metadata
TitleKONSTRUIRANJE I PRORAČUN VIŠEBRAZNOG PLUGA PRIMJENOM METODE KONAČNIH ELEMENATA
Title (english)DESIGN AND CALCULATION OF THE MULTI-FURROW PLOUGH USING THE FINAL ELEMENT METHOD
AuthorDominik Puhanić
MentorDarko Damjanović (mentor)
Committee memberDarko Damjanović (član povjerenstva)
Committee memberDražan Kozak (predsjednik povjerenstva)
Committee memberMarko Katinić (član povjerenstva)
GranterJosip Juraj Strossmayer University of Osijek
Mechanical Engineering Faculty in Slavonski Brod
Slavonski Brod
Defense date and country2020-07-24, Croatia
Scientific / art field,
discipline and subdiscipline		TECHNICAL SCIENCES
Mechanical Engineering
Abstract
Cilj je diplomskog rada konstruirati i proračunati višebrazni plug. U uvodnom dijelu rada, prikazana je osnovna podjela i vrste plužnih tijela. Na početku glavnog dijela ovoga rada, prikazana su postojeća rješenja koja će biti korištena kao sustav informacija pri daljnjem razvoju proizvoda. Tijekom konceptualne faze bile su uzete u obzir sve smjernice i zahtjevi te je izabran konačni koncept. Zatim se pristupa modeliranju pojedinih pozicija pomoću programa Siemens NX. Nakon što su izmodelirane pojedine pozicije, sklapaju se najprije u podsklopove, a zatim se podsklopovi povezuju u konačnu konstrukciju. Za numeričku analizu korištena je već ranije generirana geometrija, a cijela numerička analiza provedena je u softveru Ansys Workbench. U pojedinim podsklopovima je provjereno maksimalno naprezanje i deformacija prema stvarnim uvjetima. U analizama su provedene i konvergencije rješenja ukupnih pomaka i ekvivalentnih naprezanja po von Misesu za različite veličine konačnih elemenata koje su prikazane tablicama i dijagramima. Zatim slijedi analitički proračun određenih komponenata pluga.
Abstract (english)
The aim of this Master's thesis was to construct and calculate an plow. In the preface of this paper, there is an introduction to the basic division and types of plow bodies. At the beginning of main part of this thesis, existing solutions will be examined and used as an information system for further development of the product. During the conceptual design, all the guidelines and requirements were considered, and the final concept was chosen. The next step will be modelling of individual positions of the product with Siemens software. After certain positions have been modeled, they will be assembled in the first subassemblies, and then those subassemblies will be assembled in the finished construction. Previously made geometry was used for numerical analysis in Ansys Workbench software. Every subassembly will be checked for maximum stress and strain, based on real conditions. Convergence of solutions of total displacements and equivalent von Mises stresses for the different finite element sizes was also performed and shown in tables and diagrams. Furthermore, analytical calculation of device components is shown at the and of this thesis.
Keywords
Keywords (english)
Languagecroatian
URN:NBNurn:nbn:hr:153:799596
Study programmeTitle: Graduate Study Mechanical Engineering; specializations in: Design and Product Development, Manufacturing Logistics, Materials Engineering, Engineering Technologies, Power Engineering
Course: Design and Product Development
Study programme type: university
Study level: graduate
Academic / professional title: magistar/magistra inženjer/inženjerka strojarstva (magistar/magistra inženjer/inženjerka strojarstva)
Type of resourceText
File originBorn digital
Access conditionsAccess restricted to students and staff of home institution
Terms of useLicence In copyright icon
Created on2020-09-09 12:45:04