prikaz prve stranice dokumenta Structural Steel Joints with Bolts in Threaded Holes
  Preuzmi
PDF 1.98 MB
Znanstveni rad - Izvorni znanstveni rad
Structural Steel Joints with Bolts in Threaded Holes
Tehnički vjesnik = Technical gazette, 24(4) (2022); 1382-1393. urn:nbn:hr:237:736936
Ptiček, Marko; Skejić, Davor; Veljković, Milan; Rizzano, Gianvittorio

Institucijski repozitorij: Repozitorij Građevinskog fakulteta Sveučilišta u Zagrebu

Citirajte ovaj rad

Ptiček, M., Skejić, D., Veljković, M. i Rizzano, G. (2022). Structural Steel Joints with Bolts in Threaded Holes. Tehnički vjesnik = Technical gazette, 24(4)., 1382-1393. Preuzeto s https://urn.nsk.hr/urn:nbn:hr:237:736936

Ptiček, Marko, et al. "Structural Steel Joints with Bolts in Threaded Holes." Tehnički vjesnik = Technical gazette, vol. 24(4), 2022, str. 1382-1393. https://urn.nsk.hr/urn:nbn:hr:237:736936

Ptiček, Marko, Davor Skejić, Milan Veljković i Gianvittorio Rizzano. "Structural Steel Joints with Bolts in Threaded Holes." Tehnički vjesnik = Technical gazette 24(4) (2022): 1382-1393. https://urn.nsk.hr/urn:nbn:hr:237:736936

Ptiček, M., et al. (2022) 'Structural Steel Joints with Bolts in Threaded Holes', Tehnički vjesnik = Technical gazette, 24(4), str. 1382-1393. Preuzeto s: https://urn.nsk.hr/urn:nbn:hr:237:736936 (Datum pristupa: 28.11.2024.)

Ptiček M, Skejić D, Veljković M, Rizzano G. Structural Steel Joints with Bolts in Threaded Holes. Tehnički vjesnik = Technical gazette [Internet]. 2022. [pristupljeno 28.11.2024.];24(4):1382-1393. Dostupno na: https://urn.nsk.hr/urn:nbn:hr:237:736936

M. Ptiček, D. Skejić, M. Veljković i G. Rizzano, "Structural Steel Joints with Bolts in Threaded Holes", Tehnički vjesnik = Technical gazette, vol. 24(4), str. 1382-1393, 2022. [Online]. Dostupno na: https://urn.nsk.hr/urn:nbn:hr:237:736936. [Citirano: 28.11.2024.]

Za citiranje koristite ovu mrežnu adresu: https://urn.nsk.hr/urn:nbn:hr:237:736936
Podaci o radu
Naslov (engleski)Structural Steel Joints with Bolts in Threaded Holes
AutorMarko Ptiček
AutorDavor Skejić
AutorMilan Veljković
AutorGianvittorio Rizzano
Autorova ustanovaSveučilište u Zagrebu
Građevinski fakultet
Znanstveno / umjetničko
područje, polje i grana		TEHNIČKE ZNANOSTI
Građevinarstvo
Sažetak (engleski)
The application of tubular columns in steel structures offers many advantages. However, this potential has not been fully utilized due to a lack of access for the installation of standard bolts in end-plate beam-to-column joints. Blind bolts are an alternative way of connecting the beam end-plate to hollow section column, for they can be installed and tightened from outside of the column. Standard high strength bolts can be directly screwed into the threaded hole tapped in the column hole wall. Bolts in threaded holes (BTH) - use threads on the bolt hole wall as an anchorage instead of nuts used in standard bolt assemblies. Provisions regarding BTH can be found in the draft version of new Eurocode 3, Part 1-8, including the definition of minimum thread engagement lengths. Parametric study of beam-to- tubular column joint with extended end-plate was conducted in order to analyse the influence of BTH and specific failure modes on overall joint resistance. Minimum thread engagement length limitations were checked for all considered combinations of parameters, and based on these results, an overview of the general applicability of bolts in threaded holes was gained.
Ključne riječi (engleski)
Jezikengleski
Vrsta publikacijeZnanstveni rad - Izvorni znanstveni rad
Status objaveObjavljen
Vrsta recenzijeRecenziran - međunarodna recenzija
Verzija publikacijeObjavljena verzija rada (izdavačev PDF)
Naslov časopisaTehnički vjesnik = Technical gazette
Brojčani podacivol. 24(4), str. 1382-1393
e-ISSN1848-6339
URN:NBNurn:nbn:hr:237:736936
Datum objave publikacije2022
Vrsta resursaTekst
Prava pristupaOtvoreni pristup
Uvjeti korištenjaIkona licence Zaštićeno autorskim pravom.
Datum i vrijeme pohrane2024-09-05 05:34:49